服务热线:
18971017202
您的位置:首页 >> 新闻中心

Sb₂O₃ Masterbatch for EVA Hot-Melt Adhesives & Edgebanding

发布日期:2026-11-21 05:36:08   浏览量:0

EVA hot-melt adhesives (HMA) are widely used in furniture edgebanding, packaging, bookbinding and automotive interior bonding. Where the finished bond or the assembled part must meet a fire class (UL94, EN 13501-1, FMVSS 302, glazing/casework code), antimony trioxide masterbatch is the cleaner route over raw powder.

1. Why masterbatch over raw Sb₂O₃ powder

  • Dust & dosing accuracy: HMA lines dose small additions (2–5 phr); powder metering is error-prone and airborne Sb₂O₃ is a workplace hazard. A 30–60% masterbatch in EVA/VA carrier meters reliably in the weigh hopper.
  • Dispersion: In a molten hot-melt at 140–180°C, undispersed Sb₂O₃ agglomerates form white specks and weaken the bond line. Two-roll or twin-screw compounding pre-disperses the fine grade.
  • Lot-to-lot consistency: Masterbatch locks the effective Sb₂O₃ content per pellet, so each drum of HMA carries the declared FR loading.

2. Carrier & grade matching

  • Carrier: EVA with vinyl-acetate (VA) content matching the HMA base, typically VA 18–28%, MFI 3–20. If the adhesive is APAO/PP-based, use a PP-compatible carrier; polarity match avoids separation on recalcining.
  • Fine grade: D50 0.8–1.5 µm, purity ≥ 99.5%, white ≥ 96 (ΔE < 1), Pb < 50 ppm, Fe < 100 ppm, moisture < 0.3%. Fine particles keep haze low in semi-transparent hot-melts and reduce bond-line stress risers.
  • Halogen-antimony synergy: Sb₂O₃ is only a synergist — it needs a halogen source. With brominated flame retardants (DBDPE, TBBPA) use Br:Sb ≈ 3:1; with chlorinated paraffins use Cl:Sb ≈ 3:1, both calculated on effective halogen, not compound weight. Optional zinc borate 30–50% of the Sb₂O₃ dose reduces smoke in confined interior applications.

3. Dosing & processing

  • Effective Sb₂O₃ dose: 2.5–5 phr for most EVA HMAs; verify against the target fire class on the finished bond thickness (thin edgeband film may need a higher phr than the plaque test).
  • Melt temperature: keep ≤ 180–190°C. Above ~325°C some brominated systems release halogen and yellow; chlorinated systems degrade faster. Monitor the drum for scorch or colour shift.
  • Pre-dry: if the masterbatch has been stored above 60% RH, dry 2–4 h at 70–80°C before dosing to avoid steam pinholes and moisture-driven viscosity drift.

4. QC & verification

  • Trial before commit: run a small plaque and confirm open time, set time, and bond strength retention; target < 10% drop in peel/shear strength vs the non-FR control.
  • Fire test on the finished bond/assembly, not the HMA alone — edgebanding on a solid substrate behaves differently from a freestanding bead. Use UL94, EN 13501-1 or FMVSS 302 as the code requires.
  • Per-lot CoA: ≥ 99.5% Sb₂O₃, moisture < 0.3%, D50 0.8–1.5 µm, whiteness ΔE < 1, Pb/Fe limits. Keep a 200 g retained sample per lot for 12 months; trace batch ↔ CoA ↔ retained sample for ≥ 5 years.

Summary: Sb₂O₃ masterbatch in an EVA carrier with matched VA/MFI, fine D50 0.8–1.5 µm, ≈3:1 halogen-Sb synergy and 2.5–5 phr effective dose gives clean, consistent, regulation-ready flame retardancy in hot-melt adhesives — with the trial plaque and finished-assembly fire test as the qualification gate.

在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们