服务热线:
18971017202
您的位置:首页 >> 新闻中心

Sb2O3 Masterbatch for Glass-Filled PA66 Automotive Under-Hood Connectors & Relay Housings

发布日期:2026-11-21 05:36:09   浏览量:0

1. Why Masterbatch Over Raw Powder in Glass-Filled PA66

  • Dispersion under glass-fibre shearing: twin-screw compounding of 30-50% glass-filled PA66 generates intense shear that can re-agglomerate raw Sb2O3 fines into specks; a carrier masterbatch pre-disperses the active at 40-50% so final let-down stays homogeneous in 2.5-5 µm agglomerate-free form.
  • Dust & dosing: metering masterbatch by weight-feed eliminates airborne Sb2O3 dust at the compounder and removes per-batch manual weighing error (target ±0.1 phr consistency).
  • Moisture control synergy: a predried PA66 carrier (≤0.2% moisture) keeps the active dry at let-down, protecting against polyamide hydrolysis during melt processing.

2. Carrier Selection

  • PA66 carrier (recommended for best dispersion & property retention): melts with the base resin, minimises carrier-vs-bulk MFI mismatch, preserves long-fibre wet-out.
  • Alternatives: EVA/SAN carrier for pre-compounded glass-reinforced concentrate route; check MFI match within 10-15% to avoid short-shot or weld-line weakness in thin 1.6-0.8 mm housings.
  • Only use carrier PA66 that passes viscosity (RV) control; an off-spec carrier shifts final part viscosity and gate filling.

3. Halogen–Antimony Synergy & Dosing

  • Effective Sb2O3 dose in glass-filled systems: 4-6 wt% (on polymer fraction, not compound weight).
  • Br:Sb ≈ 3:1 molar with brominated epoxy oligomer / DBDPE (calc on effective bromine, NOT compound weight), or Cl:Sb ≈ 3:1 with chlorinated paraffin CP-52/70.
  • Glass-fibre compensation: some brominated FRs deactivate on glass surface — confirm V-0 retention on the actual 30-50% glass compound, not on unfilled plaques.
  • Zinc borate 30-50% of Sb2O3 portion for smoke suppression + anti-afterglow in under-hood fire scenarios.

4. Processing & Moisture Control

  • Pre-dry masterbatch 4-6h at 90-100°C (or as per carrier spec); compound at 260-280°C, DO NOT exceed PA66 thermal window even with high melt-flow grades.
  • Glass-filled PA66 is hygroscopic: keep hopper purge nitrogen/dry-air, moisture <0.2% at injection to avert hydrolysis-driven molecular-weight drop (mechanical loss).
  • Watch screw/plate-out & vent-starve during let-down; monitor torque stability and screen-pack pressure rise as dispersion proxy.

5. Finished-Part Qualification (Tier-1 Critical)

  • UL94 V-0 at the final wall thickness (0.8-1.6 mm connector housing) — test on live parts, not test bars.
  • Impact: notched Izod & connector mating-force retention ≥85% vs unfilled baseline.
  • Heat-aging 150°C / 1000h (or Tier-1 specified): colour shift ΔE<2, no surface bloom, dielectric/CTI retention.
  • Short-circuit / overload simulated test (RTI) where specified for relay housings.

6. CoA & Traceability Checklist

  • Purity ≥99.5% (Sb2O3 content), moisture <0.3%, D50 0.8-1.5 µm, D97 controlled, Pb<50 ppm, Fe<100 ppm, whiteness ΔE<1.
  • Halogen-free grade where RoHS/unleaded requirement applies — request CoA per lot.
  • Per-lot 200 g retained sample for 12 months; lot ↔ CoA ↔ retained-sample ↔ finished-part traceability ≥5 years.
  • Annual supplier requalification + per-lot line-trial before batch commit; demand UL/Q-mark listed grade for automotive use.

采购要点:签约/供货/收款/担责四者一致,预付≤20%配保函,四单勾稽(合同/过磅/发票/付款凭证)三额一致±0.5%,异议期外观7日/成分15-30日,CIETAC仲裁兜底,凭证绑批号归档≥5年。

在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们