服务热线:
18971017202
您的位置:首页 >> 新闻中心

Sb2O3 Masterbatch for PE-HD Industrial Products: Chemical Tanks, Pipeline Fittings & Cable Conduits

发布日期:2026-11-21 05:36:15   浏览量:0

Masterbatch vs. Raw Powder — the decision For high-density polyethylene (PE-HD) molded industrial parts (chemical storage tanks, pipe fittings, underground cable conduits), dosing Sb2O3 as a masterbatch beats dry powder feeding on three grounds: dust-free handling (no respirable Sb loss in the compounding hall), metering accuracy (consistent active loading part-to-part), and batch-to-batch whiteness consistency (no visual color drift on large moulded surfaces).

Carrier matching Use an LDPE/LLDPE carrier with MFI matching the base resin within ±10–15% so the masterbatch disperses without over-shearing or leaving gel specks. If the final part is PE-HD blow-moulded or injection-moulded, confirm the masterbatch let-down disperses in the melt before the accumulator head — otherwise a swirl pattern ("tiger striping") appears on tank walls and fittings.

Halogen–antimony synergy ratio Set the synergy by active halogen: Br:Sb ≈ 3:1 when pairing with brominated flame retardants (DBDPE, brominated epoxy oligomers), or Cl:Sb ≈ 3:1 with chlorinated paraffins (CP-52/70) or PVC sources in a co-extruded layer. Calculate on effective halogen, not compound weight — over-dosing Sb2O3 beyond the ratio window raises cost without added flame performance and can cloud translucent conduits.

Dosing window Typical active Sb2O3 loading 3–5 phr (2.5–4 wt% on polymer fraction) for UL94 V-0 at final wall thickness 3–6 mm; wall-thin parts (fittings, 1.5–2.5 mm) tend toward the higher end of the window. Combined with zinc borate 30–50% of the Sb2O3 dose for smoke suppression in confined conduit runs.

Fine-grade & dispersion Fine-grade Sb2O3 (D50 0.8–1.5 µm) to avoid white specks on smooth tank walls, bloom on long-term storage, and premature plate-out at the die/blow-pin. Verify dispersion via a two-roll mill pass and a screen-pack pressure-rise check on the extruder; reject if ΔP climbs faster than the process baseline.

Pre-dry & melt control Pre-dry the masterbatch 2–4 h at 70–80 °C when stored above 60% RH. Keep melt temperature ≤ 200–210 °C for PE-HD to avoid thermal stress cracking and dark specks; watch mould temperature cycle for sink marks that trap Sb2O3 agglomerates.

End-product qualification - Reaction-to-fire: run UL94 / IEC 60695-11-10 at final wall thickness on the finished part, not a lab plaque. - Mechanical retention: Charpy/IZOD impact ≥ 85% retained vs. unfilled baseline; -20 °C cold-crack check on fittings; 85–105 °C heat aging with no surface exudation. - Environmental stress-crack resistance (ESCR): for chemical tanks, ASTM D1693 bent-strip test — Sb2O3 loading must not push ESCR below the acceptance threshold. - Migration/leach: for potable-water-contact parts, confirm heavy-metal migration within regulatory limits (Pb, Sb release).

CoA per batch (verify before commit) - Sb2O3 purity ≥ 99.5% - Moisture < 0.3% - D50 0.8–1.5 µm (fine grade) - Pb < 50 ppm, Fe < 100 ppm - Whiteness ΔE < 1 vs. standard - Lot ↔ CoA ↔ retained-sample traceability ≥ 5 years; 200 g retained sample per lot, held 12 months; annual requalification.

在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们