服务热线:
18971017202
您的位置:首页 >> 新闻中心

Sb2O3 Masterbatch for PLA/PHA Compostable Packaging & Electronics Enclosures

发布日期:2026-11-21 05:35:47   浏览量:0

Why masterbatch over powder for bioplastics

PLA/PHA are thermally and hydrolytically sensitive. Direct powder addition risks poor dispersion, dust, and localized overheating spots that accelerate chain scission. A masterbatch on a compatible bio-carrier (PLA grade, PHA blend, or EVA with a declared melt index) gives clean dosing, fine dispersion, and batch-to-batch consistency—critical on thin-wall trays, lids, and moulded battery/enclosure parts.

Carrier matching (the make-or-break)

  • Use a PLA carrier whose IV/RFI is within ~10-15% of the host resin so it blends without viscosity shock or short-shot.
  • If the part runs PHA or a PLA/PHA blend, match carrier polarity/melt flow to the majority phase; do not assume one carrier fits all grades.
  • For moulded enclosures on injection machines, an EVA or low-MFI bio-blend carrier may widen the processing window; for film/blister, a PLA carrier is preferred to avoid haze.

Dosing window & synergy

  • Effective Sb2O3 dose: 2-4 wt% on polymer fraction for UL94 V-0/VTM-0 on finished thin walls. Do not exceed 5 wt%—above this, PLA impact strength and clarity degrade noticeably.
  • Antimony trioxide is only effective paired with a halogen source (Br:Sb ≈ 3:1 calculated on effective bromine). In compostable resin you are not adding brominated FR to the base, so carry the Br-Sb package through the masterbatch (e.g. brominated epoxy oligomer or TBBPA derivative within RoHS/REACH limits) or combine with a halogen-free system (aluminium hydroxide / magnesium hydroxide / phosphate esters) where Sb2O3 acts as a char-forming synergist. State clearly which route the grade serves.

Thermal & hydrolysis control

  • PLA: keep melt ≤190°C; PHA lower (≤170-175°C). Prolonged residence at high melt causes degradation, so keep screw residence short and watch for darkening.
  • Pre-dry masterbatch 2-4h at 70-80°C, and keep compounded moisture <0.01% (PLA hydrolyses readily; above ~0.02% you get MW drop and brittle parts).
  • Guard against plate-out / die build-up: fine-grade D50 0.8-1.5µm minimises surface specks on thin walls and keeps venting clean on injection moulds.

Qualification checks (on finished parts, not pellets)

  • Trial plaque: haze <3%, transmittance, and impact retention (drop <10% vs unmodified).
  • UL94 V-0/VTM-0 on finished wall thickness + LOI/vertical burn.
  • Thermal ageing 85°C/1000h: ΔE<2 and mechanical retention <10% drop.
  • Compostability note: if certification (EN 13432 / ASTM D6400) is claimed, verify the FR package does not fail the heavy-metal/migration limits—Sb2O3 levels must stay within the compost standard's allowable thresholds. Do not assume a flame-retardant bioplastic part is compostable-certifiable.

CoA & supplier checks

  • CoA: purity ≥99.5%, moisture <0.3%, D50 0.8-1.5µm, D97, Pb<50ppm, Fe<100ppm, whiteness ΔE<1, per-lot.
  • Retained sample 200g/12 months per lot; batch ↔ CoA ↔ retained-sample traceability ≥5 years.
  • Line-trial qualification before batch commit; annual requalification.

Supplier qualification, batch traceability, and CoA verification remain the buyer's core safeguards—see partner procurement-side documents.

在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们