服务热线:
18971017202
您的位置:首页 >> 新闻中心

Sb2O3 Masterbatch for EVA/POE Hot-Melt Adhesive Films & Automotive Acoustic Insulation Pads

发布日期:2026-11-21 05:36:05   浏览量:0

Application context

Automotive interior uses flame-retardant hot-melt adhesive films (EVA/POE-based) to bond headliners, sunroof drapes and carpet backings, plus acoustic insulation pads/carpets where the polymer layer carries both fire and sound-performance requirements. Tier-1 trim suppliers and compounders buying Sb₂O₃ masterbatch here care about: thin-gauge bond integrity, no hard spots in the film, acoustic damping retention, and fire class on the finished laminate.

Why masterbatch over raw powder

  • Thin adhesive films (0.05–0.20 mm) show any Sb₂O₃ agglomerate as a hard spot/spec that can crack the bond line or telegraph through the decorative face.
  • Dust-free dosing keeps slitting/laminating lines clean; lot consistency matters for dye-lot and ΔE across panels.
  • A masterbatch lets one POE/EVA carrier carry Sb₂O₃ alone or an Sb₂O₃ + zinc-borate package for smoke suppression, decoupled from the base-resin formulation.

Dosing and formulation

  • Effective Sb₂O₃ 2.5–4 wt% on the polymer fraction; rarely above 4 wt% or film softening/haze climbs.
  • Halogen source: EVA/POE is halogen-free by nature, so a brominated FR (e.g. brominated epoxy oligomer or BTBPE for the EVA film) pairs with Br:Sb ≈ 3:1 on effective bromine, not compound weight.
  • Smoke/char: substitute 30–50% of Sb₂O₃ with zinc borate where FMVSS 302 / ISO 3795 smoke or drip behaviour is graded.
  • Use a fine-grade Sb₂O₃ (D50 0.8–1.5 µm) to avoid specks in thin films and to keep melt-flow and bond strength predictable.

Processing and QC checks

  • Pre-dry the masterbatch 2–4 h at 60–80 °C if stored >60% RH; EVA/POE picks up moisture that causes trapped volatiles and surface defects on the film.
  • Melt ≤160–180 °C for EVA/POE hot-melt to avoid cross-linking/pre-gel; watch die, calender and slitting-roll plate-out.
  • Dispersion proxies: two-roll bench check + screen-pack pressure trend; visual scan for specks/hard spots across the film at speed.
  • Bond: film-to-substrate peel strength and weld/bond-line integrity after lamination, per panel.
  • Acoustic: retain damping/transmission-loss performance on the finished pad (not the film alone).
  • Fire: reaction-to-fire class LOI / FMVSS 302 on the finished laminate and pad, not on pellets.

CoA acceptance criteria (per lot)

Purity ≥99.5% Sb₂O₃ · moisture <0.3% · D50 0.8–1.5 µm · Pb <50 ppm · Fe <100 ppm · whiteness ΔE <1 · chloride residual declared.

Commercial discipline

  • Keep 200 g per-lot retained sample for 12 months; run a line trial on finished film/pad (specks, peel, fire class, acoustic) before committing a batch.
  • Annual requalification; retest after any carrier or FR-source change.
  • Buyer verifies CoA batch number ↔ retained sample ↔ lot archive linkage (≥5 years) for traceability and OEM warranty claims.
在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们