服务热线:
18971017202
您的位置:首页 >> 新闻中心

Sb2O3 Masterbatch for PVC/EVA Anti-Slip Floor Mats & Automotive Car Mats

发布日期:2026-11-21 05:36:06   浏览量:0

Application context

Anti-slip floor mats and door mats (home, entryway, garage) and automotive car mats are frequently PVC- or EVA-based, chosen for softness, wear resistance and cleanability. In a car cabin, the mat sits directly over the carpet and must meet interior flammability limits (China GB 8410 horizontal burning, FMVSS 302 in overseas OEs); entryway/garage mats in public buildings may face UL94 or local reaction-to-fire grading. Compounders and mat producers buying Sb₂O₃ masterbatch here care about: even flame class on the finished mat, no surface blooming or tack, dimensional stability under sun-heat, and odour/VOC compliance in cabin interior use.

Why masterbatch over raw powder

  • Painted-on or dry-blended Sb₂O₃ agglomerates show as white specks and can bloom to the mat surface (tack, dusting) — a masterbatch carries the antimony in a PVC/EVA-compatible carrier with pre-dispersed fine particles.
  • Dust-free dosing keeps extrusion/calendering and flocking/printing lines clean; lot-to-lot consistency holds ΔE and dye-lot across mats.
  • A masterbatch lets one carrier deliver Sb₂O₃ alone, or an Sb₂O₃ + zinc-borate package for smoke/char management in automotive interior grades.

Dosing and formulation

  • Effective Sb₂O₃ 3–5 wt% on the polymer fraction for typical car-mat and PVC floor-mat compounds; rarely above 5 wt% or surface tack/haze climbs.
  • PVC is inherently halogen-bearing (chlorine), so Sb₂O₃ alone gives efficient halogen–antimony synergy; trim with a metal-stearate stabiliser to keep colour and prevent premature dehydrochlorination at mat-calendering temperatures.
  • EVA is halogen-free: pair Sb₂O₃ with a halogenated FR (e.g. brominated epoxy oligomer or DBDPE) at Br:Sb ≈ 3:1 on effective bromine; or use an ATH + Sb₂O₃ partial-alternative hybrid where smoke suppression matters.
  • Use a fine-grade Sb₂O₃ (D50 0.8–1.5 µm) to keep surface smoothness and slip/feel on the anti-slip face, and to limit bloom to the top decorative layer.

Processing and QC checks

  • Pre-dry the masterbatch 2–4 h at 60–80 °C if stored >60% RH; moisture causes trapped volatiles, surface blistering and odour in closed cabins.
  • Melt ≤170–190 °C for PVC/EVA mat compounds to avoid premature cross-linking, plate-out and colour shift.
  • Dispersion proxies: two-roll bench check + screen-pack pressure trend; visual scan of the mat face for specks/bloom at line speed.
  • Fire: reaction-to-fire class on the finished mat (GB 8410 ≤100 mm/min horizontal burning, no drip igniting the base cover; UL94 rating as applicable), not on pellets.
  • Cabin-intent mats: VOC/odour and fogging check on the finished part; retain the car-mat grade separate from home-entry grade so the higher-cost formulation goes where it is required.

CoA acceptance criteria (per lot)

Purity ≥99.5% Sb₂O₃ · moisture <0.3% · D50 0.8–1.5 µm · Pb <50 ppm · Fe <100 ppm · whiteness ΔE <1 · chloride residual declared · PVC/EVA carrier compatibility documented.

Commercial discipline

  • Keep 200 g per-lot retained sample for 12 months; run a line trial on finished mat (flame class, surface bloom, odour, dimensional) before committing a batch.
  • Reverify after any carrier, FR-source or stabiliser change; annual requalification.
  • Buyer verifies CoA batch number ↔ retained sample ↔ lot archive linkage (≥5 years) for traceability and OEM warranty claims, and confirms the Sb₂O₃ purity stays under the ≥99.99% export-control threshold relevant to cross-border sourcing.
在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们