服务热线:
18971017202
您的位置:首页 >> 新闻中心

Antimony Trioxide in Rubber and Silicone Compounds: Dispersion, Loading Windows, and What Buyers Should Check on a Masterbatch CoA

发布日期:2026-11-21 05:34:43   浏览量:0

Antimony trioxide (Sb2O3) is a well-established halogen synergist not only in plastics but also in elastomer compounds. In halogenated rubbers such as polychloroprene (CR), chlorinated polyethylene (CPE), and chlorosulfonated polyethylene (CSM), Sb2O3 works with the polymer's own chlorine content to raise the limiting oxygen index and reduce smoke. In silicone rubber, high-purity fine-particle Sb2O3 is used in flame-retardant grades for cable sheathing and electronicpotting components. For buyers sourcing either powder or masterbatch for rubber applications, the evaluation points differ from plastics in several practical ways.

Why Dispersion Matters More in Rubber

Rubber mixing (internal mixer, two-roll mill) occurs at much lower temperatures than plastic extrusion — typically 80–120°C — so Sb2O3 cannot melt in or spread as easily as it does in a shear-heated polymer melt. Agglomerates that survive the mixing stage do much of their damage later:

  • Uneven flame retardance: clusters of undispersed Sb2O3 leave halogen-rich regions without a synergist partner, so LOI results vary from sample to sample even within one batch.
  • Surface defects: hard agglomerates show up as specks and protrusions on calendered sheet and extruded profiles, a common rejection reason for visible rubber goods.
  • Abrasion of equipment: coarse or gritty powder accelerates wear on mixing rolls and extruder screws.

For this reason many rubber compounders prefer pre-dispersed Sb2O3 masterbatch or treat-grade powder:聚合物-compatible binder coated particles, which incorporate faster on low-temperature mills and give a cleaner surface. When comparing suppliers, ask for dispersion test data, not just particle-size printouts.

Typical Loading Windows

Rubber compounds generally need less Sb2O3 than rigid plastics to reach a target flame rating, because the halogen level in the polymer itself already contributes:

  • CR (polychloroprene): 3–8 phr Sb2O3, often 5 phr as a starting point, sometimes paired with a small addition of zinc borate for smoke suppression.
  • CPE / CSM cable compounds: 6–10 phr, adjusted against the flame test the compound must pass (UL 1581 vertical tray, IEC 60332-1/-3, and similar).
  • Halogen-free reformulations: note that Sb2O3 does nothing without a halogen or equivalent partner; if a customer's compound is halogen-free, offering Sb2O3 is not a technical mistake worth making twice.

Loading also affects physical properties: above roughly 10–12 phr, tensile strength and elongation can begin to drop and scorch behavior may change, so the "more is safer" logic stops working in rubber faster than in plastics. Ask the compounder for their trial result and match the grade to it instead of selling a fixed high loading.

CoA Items That Matter for Rubber-Grade Sb2O3

A rubber-oriented buyer checklist on the certificate of analysis:

  1. Purity (Sb2O3 content) — 99.5% as a baseline for cable and electronics-adjacent rubber; lower-purity grades are acceptable in some general-purpose compounds but say so explicitly.
  2. Particle size distribution (D50 / D97) — fine grades (D50 around 1 µm or lower) for surface-critical items; confirm D97 so agglomerate risk is bounded, since a good D50 with a bad tail can still cause specks.
  3. Volatile matter / moisture — rubber processing at low temperature traps moisture more easily than vented plastic extrusion; excess volatile content shows up as porosity in cured stock.
  4. Whiteness or tint — matters if the compound is colored; Sb2O3 is white and can shift pale shades, so consistency batch-to-batch keeps color matching stable.
  5. Screen residue / sieve tail — some suppliers report residue on a specific mesh; this is a direct proxy for coarse-grit risk on rolls and finished surfaces.
  6. Binder and carrier declaration — for masterbatch forms, ask what polymer the carrier is and that it is compatible with the rubber system it will enter; a plastics-only carrier can hurt cure and aging.

Practical Handling Notes

Sb2O3 powder is dense and flows poorly compared with carbon black or silica; bags stored in humid warehouses can set into lumps that then read as "coarse powder" on arrival. Store sealed, off the floor, and rotate stock. If lumps form, they can usually be broken and screened, but for cable-grade work many buyers simply reserve suspect bags for non-critical compounds after retesting.

For export orders, the same documentation discipline applies as with plastics customers: batch numbers on the CoA matching the shipment, retain samples agreed in advance, and a defined window for third-party testing if dispute arises. Rubber compounders rarely reject on chemistry alone — the disputes that occur are almost always about dispersion and surface finish, which is exactly why the sieve and particle-size lines on the CoA deserve as much attention as the purity number.

在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们