服务热线:
18971017202
您的位置:首页 >> 新闻中心

Sb2O3 Masterbatch for Polycarbonate/ABS Blends: Antimony Trioxide Flame Retardant Dosing & Quality Guide (Hubei Zhongti)

发布日期:2026-11-21 05:35:13   浏览量:0

Polycarbonate/ABS blends (PC-ABS) are the standard housing resin for power tools, monitors, printers, and appliance control panels, and most of these housings require a UL94 V-0 or 5VA rating. Antimony trioxide (Sb2O3) masterbatch is the most common way to deliver the antimony half of the halogen-antimony flame retardant package in PC-ABS, but the blend presents the toughest processing window of any common engineering plastic.

What makes PC-ABS dosing different

PC-ABS has two temperature regimes to respect. The ABS phase processes comfortably at 220-240°C, but the polycarbonate phase wants 260-290°C for good melt flow, and finished parts are typically injection molded at the upper end of that range. Any flame retardant package therefore has to survive roughly 260-270°C in the melt without generating free bromine, which would degrade the polycarbonate and darken the part.

This is why the bromine source matters as much as the antimony. Decabromodiphenyl ether (decaBDE) is largely phased out; the modern choices for PC-ABS are brominated epoxy oligomers (BEO), brominated polycarbonate oligomers (BC-52/BC-58 types, with molecular weights tuned to processing temperature), and tetrabromobisphenol-A carbonate oligomers. These are engineered to stay stable at PC processing temperatures. At the same time, polycarbonate absorbs moisture readily and undergoes hydrolysis-driven chain scission above about 300°C or when melt-processed wet, so resin and masterbatch pre-drying to below 0.02% moisture is non-negotiable.

Recommended starting dosing

For a typical PC/ABS (roughly 70/30 to 80/20 PC-rich) housing requiring UL94 V-0 at 1.5-3.0 mm:

  • Brominated epoxy or carbonate oligomer: 12-15 wt% on total polymer, delivering roughly 10-12% bromine.
  • Sb2O3 from masterbatch: 4-5 wt% Sb2O3 on total polymer, which maintains the effective Br:Sb ratio near 3:1 once the carrier and additives are accounted for.

The ratio should be calculated on the bromine actually added, not on the weight of the brominated compound. If the brominated oligomer is 55% bromine by weight and you dose 14% of it, effective bromine is about 7.7%, and Sb2O3 for a 3:1 Br:Sb molar ratio lands near 3.5-4% — not the 4-5% a casual rule of thumb would suggest. Suppliers who publish this arithmetic on the CoA and in the technical datasheet make the buyer's job much easier; those who quote only "add 4%" do not.

ABS-rich blends (50/50 and below) run cooler, around 230-250°C, and can tolerate a slightly wider additive selection, but they also show more impact-strength loss from high filler loading. Keeping total mineral-plus-FR loading under about 20% protects the notched impact strength that is usually the reason PC-ABS was chosen in the first place.

Masterbatch carrier selection

Use a masterbatch carrier that is itself compatible with the blend. An ABS or SAN carrier disperses cleanly through the ABS phase; a PC carrier disperses through the polycarbonate phase. In practice, ABS/SAN carriers are the more common commercial choice because they process across the full PC-ABS window, and the carrier load (typically 30-40% on the masterbatch, i.e. 60-70% active Sb2O3) is deducted from the polymer letdown.

High-shear dispersion matters: Sb2O3 agglomerates leave white or tan specks on gloss housings, and they read as defects immediately on a dark part. Twin-screw premasterbatched material from a compounder who runs a certified dispersion QC (screen-pack pressure rise and ash-uniformity checks) avoids most of the speck complaints that drive rejections on consumer-facing parts.

Processing checklist

  • Pre-dry PC-ABS resin 3-4 h at 100-110°C; pre-dry the masterbatch per its datasheet (usually the same window). Target resin moisture below 0.02%.
  • Melt temperatures: barrel zones 250-280°C for PC-rich blends; keep residence time short and avoid dead zones at the bottom end of the screw.
  • Watch the screw and mold for plate-out: antimony salts and bromine byproducts accumulate on hot metal and eventually show up as gloss loss or a white bloom on the part. A brief production run check every 2-4 hours is enough to catch the trend.
  • Confirm the UL94 rating on the actual housing wall thickness (1.5 mm and 3.0 mm are the usual spec points) on parts molded from production resin, not lab bars.

CoA quality checks on incoming Sb2O3 masterbatch

Ask for and verify, lot by lot:

  • Sb2O3 purity ≥ 99.5%.
  • Particle size D50 in the 0.8-1.5 µm band for housing-grade work; confirm the datasheet matches the CoA.
  • Moisture ≤ 0.3%.
  • Lead < 50 ppm, iron < 100 ppm (heavy metals accelerate PC discoloration at processing temperature and are increasingly restricted under RoHS-adjacent customer specs).
  • Carrier type and loading declared on the CoA (ABS, SAN, or PC carrier; typical 60-70% active content).
  • Batch number on the CoA matching the bag number on the pallet, so retained samples and traceability line up.

Standard commercial practice from a qualified supplier: a 200 g retained sample per lot, held 12 months, and a requalification (fresh CoA plus a small-melt trial) if the masterbatch has been stored more than 12 months or if the housing shows any speck or burn-rating drift.

Hubei Zhongti supplies Sb2O3 masterbatches in ABS, SAN, and PC carriers, engineered for the PC/ABS processing window, with per-lot CoA traceability and retained-sample programs. Contact us with your blend ratio, wall thickness, and target UL94 rating for a starting formulation and sample.

在线咨询 联系方式 二维码

服务热线

18971017202

扫一扫,关注我们